#
# Original File
# -------------
#	http://www.Linux-Wireless.org/Install-HOWTO/madwifi.txt
#	http://www.Linux-Wireless.org/Install-HOWTO/Commands.iwconfig.txt ( this file )
#	http://www.Linux-Wireless.org/Install-HOWTO/NetGear.WG311.Install.RedHat.txt
#	
#	
# 20-Apr-04 amo Sepaarate out the commands
# 04-Jun-04 amo Moved to Linux-Wireless.org
# 30-Jun-04 amo Added ESSID, BSSID
#
#
#
# WEP Key Options
# ---------------
#	http://www.Linux-Wireless.org/Install-HOWTO/Commands.iwconfig.key.txt
#
#
# Operation mode : Ad-Hoc, Managed, Master, Repeater, Secondary, auto
# --------------
#	http://kbserver.netgear.com/kb_web_files/N100683.asp
#	Ad-hoc	- uses BSSID = Basic Service Set Identification
#	Managed - uses ESSID = Extended Service Set Identification 
#
# # the node is the synchronisation master or act as an Access Point
# MODE="Master"
#
# # Ad-Hoc network composed of only one cell and without Access Point
# MODE="Ad-Hoc"
#
# # Managed node connects to a network composed of many Access Points
# MODE="Managed"
#
# # If yo want to sniff the wireless connections
# MODE="Monitor"
#
# # For wireless clients
# MODE="auto"
#
#
#
# Config Options
# ---------------
#	http://www.sodan.ecc.u-tokyo.ac.jp/~okayama/memo/atheros.shtml
#	http://www.atre.t.u-tokyo.ac.jp/seminars/mech_enshu/wirelesslan.html
#
# 	http://www.wlanfr.net/forum.php?op=mess&pid=1336
#	  iwconfig ath0 mode ad-hoc
#
#	http://www.sistemistiindipendenti.org/pdf/wireless_dlink.pdf
#
#	http://mtlin.org/blog/archives/000021.html
#	  iwlist ath0 scan                list AP's the driver has scanned
#	  iwconfig ath0 essid "foo"       set the ssid to foo
#	  iwpriv ath0 mode 1              lock operation to 11a only
#	  iwpriv ath0 mode 2              lock operation to 11b only
#	  iwpriv ath0 mode 3              lock operation to 11g only
#	  iwpriv ath0 mode 0              autoselect from 11a/b/g (default)
#
#	  echo 1 > /proc/sys/net/ath/debug    enable console msgs from the driver
#	  echo 1 > /proc/net/wlan0/debug      enable console msgs from the wlan module
#	  echo hal > /proc/sys/net/ath/dump   dump h/w register state to the console
#
#
# Status
# ----------
#	iwconfig
#	iwlist
#	cat /proc/net/wireless
#
#
#
# /etc/modules.conf
# ----------------
#	...
#	alias wlan0 hostap_pci
#	post-install wlan0 iwconfig wlan0 my-essid supernet mode managed \
#		rate auto auto key XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XX open
#	...
#
#
#
# Configure the Connection
# ------------------------
#	iwlist ath0 scan
#
#	ifconfig ath0 up
#
#	iwconfig ath0 key XXXXXXXXXX
#
#	iwconfig ath0 ap MAC-Address
#	
#	iwconfig ath0 mode ad-hoc	< ad-hoc | managed >
#	iwconfig ath0 channel 1		< 1 -11 >
#	iwconfig ath0 essid your_essid_here
#	iwconfig ath0 rate 54MB
#	ifconfig ath0 192.168.1.11
#
#
#	# iwconfig Options
#	----------------
#	iwconfig ath0 mode ad-hoc channel 10 rate 54M auto essid special-ID
#		< ad-hoc | managed >
#
#
# iwconfig
# --------
#	lo        no wireless extensions.
#	eth0      no wireless extensions.
#	ath0      no wireless extensions.
#		( No wireless extensions ---> is a bad thing --> wireless card is NOT recognized )
#
#
# iwconfig Errors
# -----------------
#
# Error for wireless request "Set Mode" (8B06) :
#    SET failed on device ath0 ; Invalid argument.
# ath0      no private ioctls.
#
# Error for wireless request "Set Encode" (8B2A) :
#    SET failed on device ath0 ; Invalid argument.
#
#
# Find some supported channels
# ----------------------------
#	iwlist eth1 channel
#
#
# Find the local hotspots
# ------------------------
#	iwlist scan 
#		lo        Interface doesn't support scanning.
#		eth0      Interface doesn't support scanning.
#		ath0      No scan results
#			( No scan results ---> is a bad thing )
#
#
# http://linux-ip.net/html/tools-route.html
#	route commands
#
#
# End of file